⏳ Today Only! Grab 15% OFF + FREE Windscreen Wash + FREE Postage with Code: TODAY15 🛒

Wiper Refills: How to Buy and Fit Wiper Refills

Effective wipers are crucial for clear visibility, no matter if its morning due or heavy rain. If your wipers are streaking and screeching, you’re at risk of poor visibility and potential distractions. Replacing old and worn noisy wipers is a cheap way to get you on the road again.

Wiper refills are a practical choice since they replace only the worn rubber strip, not the entire wiper blade. Here’s how to get started with buying and fitting UNIWIPER refills:

Step 1: Finding the Correct Wiper Refills

This is the hardest part of it all. Finding and purchasing refills that match your blade’s dimensions and profile, its not just the width and length to worry about, the wiper profile also must match so it can be tricky if you dont know what profile you have because they dont have names or part numbers printed on them. Ensure the width matches to avoid fitting issues or exposing the metal frame. If they have metal spines, then check the spines after every drive to ensure they do not dislodge incase they were not installed properly.

Tools You’ll Need:

  • Combined pliers
  • Stanley knife
  • Flat-head screwdriver

Step 2: Disengage the Wiper Blade from the Wiper Arm

Removing the wiper blade from the wiper arm gives you more freedom to work. Follow these steps:

  1. Pull the wiper arm away from the windscreen until it stands upright.
  2. Turn the wiper blade 90 degrees to the wiper arm.
  3. Pinch the tab on the connector and slide the wiper blade down to disconnect it, careful not to apply excess pressure otherwise it will bend and deform the metal spine.
  4. Carefully lay the wiper arm back on the windscreen.

Step 3: Remove the Old Blade Refill

  1. Locate the metal reinforcing clip at the end of the rubber blade and push it in with pliers to release the rubber strip.
  2. Slide out the rubber strip with the metal spine on each side.
  3. Save the metal spine for the new refill, refill must be the same profile to use the same metal spine

Step 4: Insert the New Refill in Your Wiper Blade

  1. Insert the metal spine into the profile of your new refill.
  2. Ensure the refill follows the curve of the wiper blade.
  3. Slide the refill under the blade claws and push it back under the retaining clip.
  4. Trim any excess refill length.
  5. Push back the metal reinforcing clips to secure the blade.

Step 5: Reinstall the Wiper Blade onto the Wiper Arm

  1. Open the tab connector and slide the wiper blade onto the wiper arm until it locks.
  2. Ensure the connection is firm.
  3. Lay the wiper back on the windscreen.
  4. Test your wipers to ensure they work smoothly and silently.

If your wipers still make noise, try polish the glass with a good glass polish.

Why Choose UNIWIPER Wiper Blades

For a hassle-free experience, consider replacing your entire wiper blade with UNIWIPER wiper blades. Our blades are easy to buy and install, taking less than five minutes. They feature Teflon and graphite for a smooth, silent wipe, and work flawlessly in all weather conditions.

Comparison:

Feature UNIWIPER Wiper Blades Ordinary Blade Refills UNIWIPER Refills
Buying Process Easy, car-specific navigation Measure and shop around Easy, one blade fits all our front refillable blades
Fit Guaranteed perfect fit May not fit perfectly Fits all UNIWIPER aero and beam blades
Installation Time Less than 1 minutes Time-consuming to source and also tricky to install Less than 5 minutes
Tools Required None Pliers, scissors, screwdriver Scissors

Order your new UNIWIPER blades today and enjoy fast shipping across Australia.

 

Frequently Asked Questions

 

Do you sell wiper blade refills?

Yes, we do. UNIWIPER offers wiper refills to fit our beam and aero blades. When you purchase refills with your wiper blades, we send refillable blades that fit perfectly. We offer two types of blades, refillable and non-refillable so its important to buy refills with your purchase to ensure you receive blades that can be refilled otherwise you may receive an enclosed unit that cannot be refilled.

How do I install my new wiper blades?

Installation is quick and easy. Simply disengage your old wiper blades and insert the new ones. Refer to steps 2 and 5 above or watch our instructional video provided with your order.

 

Over 10,000+ Wiper Blades Sold Last Month!
Find Your Wipers & SAVE OVER 50% TODAY! compared to dealership pricing
Free Delivery Across Australia

If you can't find your car in the list, please scroll down to ensure you haven't missed it. If you're not 100% sure, select the option you think is closest. A photo of the car will be shown to help you confirm if it's the correct model. If you still can't find your car, please fill out the form below with your vehicle details and we'll respond shortly.

Enter valid email address!

Your name and Email Address is required field!

do not allow HTMLTAGS!

Thank you for your inquiry. We will check and get back to you shortly.